ข้ามไปยังเนื้อหาหลัก
กลับไปโปรไฟล์ผู้เชี่ยวชาญ

ผศ.ดร.วิรัช ทวีปรีดา

ผลงานตีพิมพ์ทั้งหมด

76 public publications

Page size102550

Preparation and Characterization of PVDF–TiO2 Mixed-Matrix Membrane with PVP and PEG as Pore-Forming Agents for BSA Rejection

Rianyza Gayatri, Ahmad Noor Syimir Fizal, Erna Yuliwati, Md. Sohrab Hossain, Juhana Jaafar, Muzafar Zulkifli, Wirach Taweepreda, Ahmad Naim Ahmad Yahaya

Nanomaterials · 2023

Polymeric membranes offer straightforward modification methods that make industry scaling affordable and easy; however, these materials are hydrophobic, prone to fouling, and vulnerable to extreme operating conditions. Various attempts were made in this study to fix the challenges in using polymeric membranes and create mixed-matrix membrane (MMMs) with improved properties and hydrophilicity by adding titanium dioxide (TiO2) and pore-forming agents to hydrophobic polyvinylidene fluoride (PVDF). The PVDF mixed-matrix ultrafiltration membranes in this study were made using the non-solvent phase inversion approach which is a simple and effective method for increasing the hydrophilic nature of membranes. Polyvinylpyrrolidone (PVP) and polyethylene glycol (PEG) as pore-forming chemicals were created. Pure water flux, BSA flux, and BSA rejection were calculated to evaluate the mixed-matrix membrane’s efficiency. Bovine serum albumin (BSA) solution was employed in this study to examine the protein rejection ability. Increases in hydrophilicity, viscosity, and flux in pure water and BSA solution were achieved using PVP and PEG additives. The PVDF membrane’s hydrophilicity was raised with the addition of TiO2, showing an increased contact angle to 71°. The results show that the PVDF–PVP–TiO2 membrane achieved its optimum water flux of 97 L/(m2h) while the PVDF–PEG–TiO2 membrane rejected BSA at a rate greater than 97%. The findings demonstrate that use of a support or additive improved filtration performance compared to a pristine polymeric membrane by increasing its hydrophilicity.

Modification of chitosan-based membrane with epoxidized natural rubber for PEMFC application

Anuchit Wichianchom, Wirach Taweepreda, Qamber Ali, G. Arthanareeswaran

Journal of Rubber Research · 2023

NaCMC-decorated ZnO nanocomposite polymer membranes for the separation of reactive dyes from textile water

R. Robin, Vinoth Kumar Raja, Rajnish Kumar, G. Arthanareeswaran, Wirach Taweepreda

New Journal of Chemistry · 2023

Nanostructured ZnO/carboxymethyl cellulose nanocomposite-embedded polymer membranes developed for the removal of reactive black 5 (RB5) dye from textile water.

Correction: NaCMC-decorated ZnO nanocomposite polymer membranes for the separation of reactive dyes from textile water

R. Robin, Vinoth Kumar Raja, R. Sathish Kumar, G. Arthanareeswaran, Wirach Taweepreda

New Journal of Chemistry · 2023

Correction for ‘NaCMC-decorated ZnO nanocomposite polymer membranes for the separation of reactive dyes from textile water’ by R. Robin et al. , New J. Chem. , 2023, 47, 20517–20526, https://doi.org/10.1039/D3NJ03783E.

Effect of TiO2 concentration in PVDF-TiO2-PVP mixed matrix membrane performance using ultrafiltration process

Rianyza Gayatri, Erna Yuliwati, Ahmad Noor Syimir Fizal, Muhamad Zulhilmi Zailani, Juhana Jaafar, Muzafar Zulkifli, Wirach Taweepreda, Ahmad Naim Ahmad Yahaya

Materials Today Proceedings · 2023

Deproteinization of Natural Rubber Latex and Its Pale-Colored Thin Films

Jirapornchai Suksaeree, Chanin Bumroongrat, Nantanat Polraksa, Wirach Taweepreda, Thawatchai Phaechamud, Wiwat Pichayakorn

Sustainability · 2023

The non-rubber components present in natural rubber latex can contribute to the dark color of dried films and may cause allergic reactions. This project aimed to develop light-color rubber films with minimal protein contamination. Various additives were incorporated, and a leaching procedure was implemented to address this issue. The evaluation focused on protein content, color changes, and swelling properties of thin natural rubber films. Texapon N70 proved effective as both a latex stabilizer and leaching agent, while Uniphen P-23 served as a preservative. The combined use of these additives facilitated the removal of soluble serum through appropriate incubation, leaching, and centrifugation processes. The introduction of additional centrifugation cycles improved deproteinization and color reduction; however, it led to a loss of rubber mass and an increase in manufacturing costs. Increasing the amount of Texapon N70 and introducing alkali potassium hydroxide (KOH) further enhanced the efficiency of deproteinization and color reduction. The optimal conditions determined in this investigation were as follows: 0.5% w/w Texapon N70, 0.5% w/w KOH, 1% w/w Uniphen P-23, a 60-min incubation period, and a single leaching cycle with distilled water. These conditions resulted in a 90.57 ± 1.20% decrease in protein contamination and a color change (ΔE) of 433.69 ± 20.23. This successful condition can be replicated and scaled up for further applications.

Exploring the potential of thermophilic anaerobic co-digestion between agro-industrial waste and water hyacinth: operational performance, kinetic study and degradation pathway

Audrey Chai, Yee‐Shian Wong, Soon‐An Ong, Nabilah Aminah Lutpi, Sam Sung Ting, Wirach Taweepreda, Wei-Chin Kee, H.H. Khoo

Bioprocess and Biosystems Engineering · 2023

Impact of Climate Change on Cassava Yield in Nigeria: An Autoregressive Distributed Lag Bound Approach

Casmir Ndukaku Anyaegbu, Kingsley Ezechukwu Okpara, Wirach Taweepreda, David Akeju, Kuaanan Techato, Robert Ugochukwu Onyeneke, S. Poshyachinda, Siwatt Pongpiachan

Agriculture · 2022

Across the globe, climate change is threatening the environment, crop yield and food security. The key to ensuring a sustainable environment, crop yield increase and food security is to identify the long-term significant impact of climate change and the means of reducing the effect. This study examined the impacts of climate change on cassava yield in Nigeria. Data were sourced from the Climate Change Knowledge Portal and the Food and Agricultural Organization of the United Nations spanning from 1990 to 2019. The impact of climate change was analyzed using Autoregressive Distributed Lag Bound approach, Error Correction Model and Augmented Dickey–Fuller and Phillips–Perron tests for stationarity test. The model was subjected to diagnostic tests such as stability tests, normality tests, serial correlation tests and heteroscedasticity tests. With the exception of temperature, the study revealed that arable land, rainfall and greenhouse gases such as C2O, nitrous oxide and methane had a long-term significant impact on cassava yield in Nigeria. The study also noted that methane causes long-term significant damage to cassava yield more than any other greenhouse gas and climatic variables in the study. We recommended policies and programs that facilitate the uptake of climate-smart agriculture that centers on greenhouse gas emission reduction and on crop improvement research by breeding crop varieties that will be resilient to climate shocks.

Advanced extraction and separation approaches for the recovery of dietary flavonoids from plant biomass: A review

S. A. Gokula Krishnan, G. Arthanareeswaran, Gnanaselvam Gnanasekaran, Zsuzsanna László, Gábor Veréb, Szabolcs Kertész, Wirach Taweepreda

Biomass Conversion and Biorefinery · 2022

Investigation of intrinsic bisphenol separation capacity of zeolitic imidazolate framework-8 based membranes

Sujithra Sundarajan, Yohannan Subin Sabilon, G. Arthanareeswaran, Wirach Taweepreda

Desalination and Water Treatment · 2021

ABSTRACT The present study deals with the synthesis of polyetherimide (PEI)-based membrane with zeolitic imidazolate framework (ZIF) nanoparticles as fillers by wet phase technique. The synthesized membranes were characterized based on their physical and chemical properties and were used to study the effective removal of Bisphenol A (BPA) from water. After the BPA removal with different membrane compositions, it was found that 1% PEI/ZIF-8 mixed matrix membrane gave maximum BPA rejection of 94.1% in comparison with other membranes. The flux recovery ratio of 0.92 was also found to be the highest for 1% PEI/ZIF-8 membrane which shows that this membrane has undergone the least fouling when compared to other membrane compositions. Overall, a 1% concentration of PEI/ZIF-8 membrane showed better characteristics and a maximum percentage of BPA removal was obtained.

Improvement of the Mechanical Properties by Guar Gum Addition of Epoxidized Natural Rubber/Polyethylene Glycol Composite Membranes

Kritsada Phatcharasit, Wirach Taweepreda

Lecture notes in mechanical engineering · 2021

Propranolol Hydrochloride Film Coated Tablets Using Natural Rubber Latex Blends as Film Former

Wiwat Pichayakorn, Kamon Panrat, Jirapornchai Suksaeree, Wirach Taweepreda

Journal of Polymers and the Environment · 2021

Energy conversion from wastewater sewage sludge

Arif Billah, Kuaanan Techato, Wirach Taweepreda

Asia-Pacific Journal of Chemical Engineering · 2020

Abstract Natural rubber‐based industries in Southern Thailand are generating concentrated latex sewage sludge (CLS), which is commonly managed by landfilling practice that is causing serious environmental hazards. The purpose of this study was to develop a method to produce pellets using CLS and para‐wood sawdust as a potential biomass source for energy generation. The process started with dewatering the CLS through a decanter centrifuge. Then a flat die pellet mill was applied for copelletization. Finally, the pellets were investigated to evaluate the higher heating value and toxic heavy metals (Cu, Zn, Cr, As, Cd, and Pb) using proximate ‐ ultimate analysis, fourier transform infrared analysis, scanning electron microscopy, calorific value, thermogravimetric analysis, atomic absorption spectrometer, and inductively coupled plasma optical emission spectroscopy. The results showed that the addition of the para‐wood sawdust resulted in higher heating value and lower ash content of 3,620 ± 12 kcal/kg and 4.93 ± 0.98%, respectively. Besides, it has increased the carbon content of the pellet from 28.23 to 46.26% highest among all the samples. Furthermore, the method developed in this study is not only environmentally friendly but also economically sound than the earlier management of CLS.

Preparation and characterization of polymer electrolyte membrane from chloroacetate chitosan/chitosan blended with epoxidized natural rubber

Qamber Ali, Wirach Taweepreda, Kuaanan Techato

Polymer Testing · 2019

The effect of field natural rubber latex pretreatment with cationic exchange resin on latex dipped film properties

S. Kaewthai, Sineenart Puangmanee, Wirach Taweepreda

Journal of Rubber Research · 2019

Mechanical and Morphological Properties of Sulfur-Cured Natural Rubber/Polyethylene/Epoxidized Natural Rubber Blends

Kritsada Phatcharasit, Wirach Taweepreda, Patompong Phummor

Key engineering materials · 2017

The polymer blend was prepared from natural rubber (NR) and polyethylene (PE) powder blended with epoxidized natural rubber (ENR) by using an internal mixer. In this study, epoxidized natural rubber (ENR) was used as compatibilizer for the blends. Blending ENR with PE powder and NR were prepared at various compositions from 0-20% by weight. Then, specimens from the blends were produced by compression molding at 150 °C. The mechanical and morphological properties of the composites were investigated. It was found that the addition of ENR content has improved the tensile strength, compression set and hardness for the ternary compositions composed of NR/PE powder/ENR compared to the binary one (i.e. NR/PE powder). ENR contributed to a better dispersion between the NR and PE phases as observed in the scanning electron microscopy.

Effect of Low Molecular Weight Natural Rubber on Mixing and Vulcanized Properties of Low Energy Processing Natural Rubber

Saengchao Thongseenuch, Wirach Taweepreda, Krisda Suchiva

Sains Malaysiana · 2017

Compounding of natural rubber (NR) requires high energy due to the high viscosity characteristic of NR. In order to reduce the viscosity, low molecular weight of NR (LNR) latex was prepared from field latex by using oxidative phenyl hydrazine/O 2 system. LNR latex was mixed with high ammonium NR latex at 3, 5 and 10 phr to provide low energy processing NR (LEPNR). Viscosity molecular weights (Mv) of obtained LNR were 42.59, 18.42 and 6.66 kg/mol, respectively. It was found that the maximum Mooney viscosities and ML 1+4@100C of LEPNRs were significantly decreased with a decrease of Mv of LNR and an increase of LNR content as well. Specific mixing energy consumptions for mastication step and carbon black incorporation step in Brabender Plasticorder were characterized. The results showed that the mixing energy consumption decreased with an increase of LNR content and a decrease of Mv of LNR. Furthermore, an addition of LNR lowered the viscosity of the compounded rubber, slightly shortened the scorch time, and significantly changed the cure time. Although LNR dropped 50% and 100% modulus of vulcanized rubber, it slightly effected the tensile strength of the vulcanized rubber.

Fabrication and Properties of Rubber Nanofiber from Electrospinning

Wirach Taweepreda

InTech eBooks · 2017

Electrospun nanofibers of rubber blending with poly(vinyl chloride) (PVC) were prepared by electrospinning. Various concentrations of rubber solution were added to the PVC solution for several purposes of the electrospun nanofibers. The pristine and rubber plasticized nanofibers were characterized by field emission scanning electron microscopy (FE‐SEM), differential thermal analysis (DTA), and thermogravimetry analysis (TGA), respectively. Thermal properties from DTA and TGA results indicated that the addition of rubber decreased glass transition temperature (Tg) of PVC and increased heat resistance of PVC nanofiber. The dielectric constant of plasticized nanofibers measured using precision LCR meter indicated that the membranes were dense.

Electrochromic properties of MoO3-WO3 thin films prepared by a sol-gel method, in the presence of a triblock copolymer template

Phuriwat Jittiarporn, Lek Sikong, Kalayanee Kooptarnond, Wirach Taweepreda, Stefan Stoenescu, Simona Bǎdilescu, Vo‐Van Truong

Surface and Coatings Technology · 2017

Preparation and molecular weight controlled of liquid natural rubber using Mastication

Saengchao Thongseenuch, Sopapan Jindapaisan, Wirach Taweepreda

2016

Natural rubber (NR) can be easily depolymerized because that contain unsaturated component (double bond). Mastication is breaking the rubber molecular chains through mechanical action and thermal in two roll mill. This attention is preparation depolymerized natural rubber, using mastication method with temperature-controlled two roll mill. The effect of temperature and time of mastication on degree of depolymerization were studied and characterized by Gel Permeation Chromatography (GPC). It was found increasing temperature and time of mastication to the resulting decreased average molecular weight of NR.

Synthesis of h-MoO3 and (NH4)2Mo4O13 Using Precipitation Method at Various pH Values and their Photochromic Properties

Phuriwat Jittiarporn, Lek Sikong, Kalyanee Kooptarnond, Wirach Taweepreda, Pipat Chooto, Matthana Khangkhamano

Applied Mechanics and Materials · 2016

(NH4)2Mo4O13 and h–MoO3 nanocrystalline powders were synthesized by precipitation method at a varied pH range from 5.0 to 1.0. The crystal structure, morphology and optical property of samples were determined by X–ray diffractometer (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and UV–vis diffuse reflectance spectrophotometer (UV-vis DRS). At pH 2.0, 3.0 and 5.0, homogenous plate–like (NH4)2Mo4O13 was seen, whereas the heterogeneous hexagonal rod–shaped MoO3 was found at very low pH of 1.0 and 1.5. Band gap energy of the synthesized (NH4)2Mo4O13 and h–MoO3 were 3.38 and 3.18 eV, respectively. Photochromic properties of the products were illustrated by color difference before and after UV irradiation using CIE Lab color system. The synthesized h–MoO3 provided a strong photochromic performance, while the (NH4)2Mo4O13 showed non–photochromic properties. Intercalation of H+ in h-MoO3 were studied using electrochemical characterization by cyclic voltammetry (CV). The diffusion coefficient of the samples increases with decreasing pH of the solution.

Coating of porous PVC-PEG memebrane with crosslinkable XSBR for O2/N2 and CO2/N2 separation

Chanaphan Lamlong, Wirach Taweepreda

Polymer · 2016

Preparation and Characterization of Natural Rubber/Chitosan Films

Kansiree Paoribut, Wirach Taweepreda, Kanoktip Boonkerd

Key engineering materials · 2015

Natural rubber/chitosan (NR/CS) films at various NR/CS ratios were prepared here from the mixture of natural rubber latex (NRL) and chitosan solution using a solution casting method. The NRLs with and without sulfur curing agents were used. The NR/CS films were obtained after heating at 50oC for 24 hours. The NR/CS films prepared from the NRL with curing agents were further heated at 120oC for 30 min to acquire the NR networks. From swelling testing, it was found that incorporation of CS into the NR matrix gave the films with higher solvent resistance. The swelling index reduced proportionally with the increased CS loadings. Additionally, the solvent resistance of the NR/CS films was improved more once the NR was cured. In general, for every NR/CS ratio, the tensile strengths of the cured NR/CS films were higher than those of the uncured NR/CS films. After thermal aging, it was found that the tensile strength of the uncured NR/CS films decreased while that of the cured ones increased. Two thermal decomposition peaks were observed. The onset decompostion temperatures at lower and higher temperature were corresponding to the degradation of chitosan and natural rubber, respectively. The initial thermal degradation temperature of CS and NR in the NR/CS films was shifted to the higher temperature than that of the pure CS and NR, respectively.

Surfactant Treatment and Leaching Combination Process for Preparation of Deproteinized Natural Rubber Latex

Jirapornchai Suksaeree, Wirach Taweepreda, Wiwat Pichayakorn

Key engineering materials · 2015

This study aimed to improve the efficacy of protein removal from fresh natural rubber latex (NRL) and to decrease the production cost by using surfactant treatment and leaching combination processes. The 0.5-3% anionic surfactants, i.e. sodium dodecyl sulfate or sodium lauryl ether sulfate, nonionic tween80 surfactant, or an amphoteric cocamidopropyl betaine surfactant was used in surfactant treatment process. Moreover, water, aqueous surfactant solutions, and/or 1-5% organic solvents (i.e. ethanol, isopropanol and/or acetone) was then used in leaching process. The fresh NRL was preserved by paraben compounds in the presence of surfactant at ambient temperature for 20-120 minutes, and then centrifuged. This might prevent the skin irritation of deproteinized NRL (DNRL) caused by ammonium stabilizer that normally uses in latex industry. The upper rubber mass was then leached for upto three cycles with leaching solvents, and then finally redispersed in distilled water. The milky-like DNRLs were obtained by these processes. Their dry rubber contents were 41-47% that could be adjusted. Their viscosities were 9-13 centipoises with the pH of 6.04-6.61. The protein residues in these DNRLs were 0.0000-0.3244% which were lower than that of fresh NRL (1.2428%). These indicated the efficacy of studied deproteinization process for 73.90-100.0%. Types and concentrations of surfactant, incubation times, leaching solvents, and cycles of leaching process affected the efficacy of deproteinization process. Moreover, the properties of these dried films were not different from that of fresh NR film. This DNRL could be further used for several applications including medical skin products.

Properties of Deproteinized Natural Rubber Latex/Gelatinized Starch Blended Films

Rungtiwa Waiprib, Wiwat Pichayakorn, Prapaporn Boonme, Wirach Taweepreda, Jirapornchai Suksaeree

Key engineering materials · 2015

This research aimed to study the compatibility and properties of deproteinized natural rubber latex (DNRL)/gelatinized starch blended films for use as transdermal patches. Various starches were previously gelatinized by heat treatment. Then, the DNRL/gelatinized starch blended films were prepared by simple mixing of DNRL with gelatinized starch and then drying at 50°C. The various parameters such as types (potato, sago, bean, corn, tapioca, rice and glutinous starches), amounts (5, 10, 15 and 20 part per hundred of rubber (phr)) and concentrations of gelatinized starch pastes (5, 10, 20 and 50%) were evaluated. It was found that all starch types could be blended as a homogeneous mixture with DNRL only in 5 phr. Bean starch also provided the good mixture in 10 and 15 phr. Rice and corn starches in the concentrations up to 20 phr could also be blended. Higher concentration of gelatinized starch pastes obtained the higher viscous liquids that were difficult to blend as a homogeneous mixture with DNRL, and provided inhomogeneous blended films. The dried films of all homogeneous DNRL/gelatinized starch mixtures were slightly yellowish transparent with good physical appearances. The tensile strength, swelling and erosion of these blended films increased when increasing amounts of gelatinized starch, but their elasticities were not different comparing to that of DNRL film itself. However, their strengths should be further improved by adding some plasticizers. Some drugs would be further loaded in these homogeneous film formulations for transdermal delivery.

Page 2 of 4

การใช้คุกกี้วิเคราะห์

เว็บไซต์นี้ใช้ Google Analytics เพื่อดูภาพรวมการใช้งาน เช่น จำนวนผู้เข้าชมและหน้าที่ได้รับความสนใจ โดยจะเปิดใช้เมื่อคุณยอมรับเท่านั้น

ยังไม่ได้เลือก