ข้ามไปยังเนื้อหาหลัก
กลับไปโปรไฟล์ผู้เชี่ยวชาญ

ผศ.ดร.วิรัช ทวีปรีดา

ผลงานตีพิมพ์ทั้งหมด

76 public publications

Page size102550

Investigation of Sulfur Crosslinking Interfacial of Natural Rubber (NR) Blending with Carboxyalted Styrene Butadiene Rubber (XSBR) Using X-Ray Absorption Spectroscopy

Chanaphan Lamlong, Wirach Taweepreda, Rattapong Nu-Mard, Prayoon Songsiriritthigul

Advanced materials research · 2015

The sulfur crosslinking films from Natural Rubber (NR), Carboxylated Stryrene Butadiene Rubber (XSBR) latices, and their blends have been investigated using X-ray absorption near-edge structure spectroscopy (XANES). The film was prepared by casting the latex compound on glass surface and heating at 120oC in a hot air oven for 10 minutes. The sulfur crosslinking density were studied by the XANES. This was done to provide the local geometry and electronic environment of sulfur bonding in the rubber networks. We found that the reversion takes place before the onset of oxidative processes at the sulfur bridges. Parallel to the oxidative processes, the production of cyclic sulfanes takes places. This relationship depends on the rubber compositions.

Influence of N-Doped TiO2 Nanocomposite Film on Hydrophilic Property of Rubber Dipping Former Surface

Mahamasuhaimi Masae, Lek Sikong, Kalayanee Kooptarnond, Wirach Taweepreda, Fumio Saito, Pichaya Pitsuwan

Key engineering materials · 2014

The objective of this study is to explore a method to improve hydrophilicity of the surface of formers that could be more easily dipped to produce high quality dipped rubber products. Photocatalytic TiO2 composite films were prepared by sol-gel method. Glass formers were coated with nitrogen doped TiO2 nanocomposite film by dipping method and annealed at 600°C for 1 h. Phase formation of TiO2 was characterized by XRD. Morphology of the TiO2 films was observed by using atomic force microscopy (AFM). Optical absorption of the films and degradation concentration of methylene blue had been measured employing UV-Vis spectrophotometer. The hydrophilicity of the thin films was determined in terms of the contact angles of water and NR rubber latex droplets on the coated TiO2 composite films under visible light irradiation. It was found from the experimental study that the TiO2 nano-composite film can improve wet-ability of the coated former surfaces.

Rheological Behavior Characterization of Natural Rubber Containing Different Gel

Saengchao Thongseenuch, Wirach Taweepreda, Krisda Suchiva

Advanced materials research · 2014

This research, natural rubber containing different gel contents were prepared by deproteinization and saponification treatment from high ammonium natural rubber latex. Deproteinization natural rubber was further treated as acetone extraction and then transesterification. It was founded that gel content and molecular weights of treated natural rubber were decreased and almost absented for transesterification treatment. Rheological respond on small amplitude oscillating shear (SAOS) and large amplitude oscillating shear (LAOS) deformation of treated natural rubber were captured by using rubber process analyzer (RPA 2000). Firs harmonic rheological properties, storage modulus, G and loss modulus, G decreased as gel content and molecular weight decreased. It was believed that gels, explicitly branching points, were destroyed after the natural rubber was deproteinized, transesterification, or saponification according to the molecular structure of natural rubber presumed by Tanaka et al, which functional groups contain protein and fatty acid are participated in branching to forming gel structure. It was concluded that gel content as the same as molecular structure of natural rubber could be characterized as rheological behavior.

Preparation of Positively Charged Membrane from Natural Rubber Latex Blending with Chitosan

Wirach Taweepreda, Supawadee Tuaybut, Sineenart Puangmanee, Tran Dang Khoa

Communications in Physics · 2014

Film formation of natural rubber latex (NRL) blended with various concentrations of chitosan was investigated. Atomic force microscopy (AFM) images clearly showed that the NRL film covered chitosan phase. Roughness of the films which was calculated from AFM image increases with increasing chitosan concentration. Miscibility of NRL and chitosan in solution was investigated by using dynamic mechanical thermal analysis (DMTA) and found that chitosan incorporated with NRL less than 40 weight percentage (wt%) was partially miscible. Films of the chitosan blending with higher NRL contents exhibited two peaks of glass transition temperatures. Interfacial polarization and dielectric properties of polymer films were improved with increasing NRL contents. Chemical structure of the blends was characterized by using attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR).

Electrospun Conditions of Poly(vinyl chloride) Nanofibrous Membrane Plasticized with Polyurethane

Kritsada Phatcharasit, Wirach Taweepreda, Kanoktip Boonkerd, Jin‐Kuk Kim

Jurnal Teknologi · 2014

Electrospun poly(vinyl chloride) (PVC) nanofibrous were prepared by electrospinning. Various concentration of polyurethane (PU) were added to PVC solution for plasticization of the electrospun nanofibrous. The pristine and plasticized nanofibrous were characterized by field emission scanning electron microscopy (FE-SEM), differencial thermal analysis (DTA), and thermogravimetry analysis (TGA), respectively. Thermal properties form DTA and TGA results indicated that the addition of PU decreased glass transition temperature (Tg) of PVC and increased heat resistance of PVC nanofiber. The dielectric constant of plasticized nanofibrous measured using precision LCR meter indicated that the membrane were dense.

Effects of precipitation temperature on the photochromic properties of h-MoO3

Phuriwat Jittiarporn, Lek Sikong, Kalayanee Kooptarnond, Wirach Taweepreda

Ceramics International · 2014

Feasibility Studies of Magnesium (II) Removal from Fresh Field Natural Rubber Latex Using Macroporous Cationic Exchange Resin

Sineenart Puangmanee, Wirach Taweepreda

Advanced materials research · 2013

The presence of magnesium ions (Mg2+) in fresh field natural rubber latex (FF-NRL) is a major concern for concentrated production. In general, Mg2+ is reduced by adding diammonia hydrogen orthophosphate (DAP) to FF-NRL. The reaction rate between DAP and Mg2+ in NRL is very slow and is the cause of waste latex sludge, waste time for more than 12 hours, and chemicals loss. Moreover, the waste latex sludge is toxic and has to be treated. In this research, the possibility of using cationic exchange resin to remove Mg2+ from the FF-NRL was investigated. The experiment was carried out by comparison the efficiency of difference commercial exchange resin on Mg2+ reduction rate after immersing in FF-NRL. The results were found that macroporous cationic exchange resin adsorped Mg2+ with highest rate. The Mg2+ content of NRL reduced to 100 ppm after immersing macroporous cationic exchange resin in FF-NRL for 6 hours. The performance of cationic exchange resin was increased after regenerate process with acid and can be used for further to reduce Mg2+ in FF-NRL. The morphology of cationic exchange resin was investigated using scanning electron microscope (SEM).

Green Lightweight Concrete Made from Natural Para Rubber Product

Duangden Raksritong, Danupon Tonnayopas, Wirach Taweepreda, Manoon Masniyom

Key engineering materials · 2013

Para Rubber Seed Shell (PRSS) as a coarse aggregate and coated by vulcanization and mixing epoxy natural rubber (ENR) was investigated. Natural rubber latex (60% DRC) was applied in two stages. Firstly stage, synthetic natural latex (ENR-35) solution was coated on the first layer of PRSS. After that, PRSS was coated by vulcanization in second layer. Then, pre-wetting was performed before mixing or casting the concrete for 5 days. Finally, CPRSS (Coated Para Rubber Seed Shell) was produced. The CPRSS aggregate was cast as self consolidation concrete (SCC) with different ratios of ordinary Portland cement: sand: CPRSS for 0.8-1: 0.6-0.85: 0.04-0.12 by weight, respectively and constant water/binder ratio at 0.45 throughtout this study. The ENR-35 was also used about 5% of the water content. However, the concrete was wrapped with polyvinyl sheet to prevent moisture loss during setting and curing in ambient temperature (29°C, 84%RH) for 28 days. The fresh concrete to slump test, harden concrete with bulk density and compressive strength of whole formulations was carried out to determine. The test result A8 indicted that the most ingredient suitable mixture of SCC involed cement: sand: CPRSS of 1:0.94:0.046. The SCC contained the slump as 120 mm, bulk density about 1916 kg/m3 and compressive strength was 37 MPa. Its was met specification of structural lightweight concrete. This beneficiation of SCC is also product as the green innovation building in terms of construction materials and resources, leaving minimal environmental impact, and having energy saving and eco-friendly materials.

Electrospun Epoxidized Natural Rubber with Poly(vinyl chloride) (ENR-PVC) Nanofibrous for PEMFC Applications

Kritsada Phatcharasit, Wirach Taweepreda, Kanoktip Boonkerd, Jin Kuk Kim

Advanced materials research · 2013

Various electrospun epoxized natural rubber / poly (vinyl chloride) (ENR/PVC) blend nonwoven membranes were prepared by electrospinning technique. Various concentration of epoxidized natural rubber (ENR) solution in N,N-dimethylformamide (DMF) were directly added to PVC solution for plasticization of the electrospun nanofibrous. Differencial thermal analysis (DTA), thermogravimetry analysis (TGA), fourier transfrom infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM) were used to characterize the pristine and plasticized nanofibrous. DTA results indicated that the addition of ENR resulted in the shifting of glass transition temperature (Tg) towards lower temperatures. The blending of PVC with ENR is thermodynamically incompatible.

Fabrication and Characterization of Epoxidized Natural Rubber-Chitosan Membrane

Wirach Taweepreda, Anuchit Wichianchom

Advanced materials research · 2013

The membranes obtained from the mixtures of epoxidized natural rubber latex (ENR) and chitosan solution were prepared and characterized. The chemical structure of the membrane was confirmed by ATR-FT-IR spectroscopy and found the peak at 1315 and 1155 cm-1 indicated ether linkage was formed between epoxide group and chitosan corresponding with an enhancement of their mechanical properties which were observed using dynamic mechanical thermal analysis (DMTA). The dielectric properties and ionic conductivity of membrane were investigated using LCR meter and found that the ionic conductivity was increased with increasing the chitosan content.

Page 6 of 8

การใช้คุกกี้วิเคราะห์

เว็บไซต์นี้ใช้ Google Analytics เพื่อดูภาพรวมการใช้งาน เช่น จำนวนผู้เข้าชมและหน้าที่ได้รับความสนใจ โดยจะเปิดใช้เมื่อคุณยอมรับเท่านั้น

ยังไม่ได้เลือก